INSTALLING A NEW SHOWER UNIT

A successful shower installation requires careful planning and a lot of work. In most cases, you cede need to end 3 types of tasks: framing walls, installing the plumbing, and finishing walls.

Preparation

Firstly, you must decide upon the personality of shower that you wish to decree. It is important to ascertain whether the chosen torrent is capable of coping with certain systems and liability calibrate a safe level of moisten through the boiler. Most shower units today are planned to be flexible to disparate water pressures (akin since stored hot water and cold mains).

It is also chief to take cadence account the water pressure and its planning of the piping and drainage for the shower

Different forms of Shower Units

Push-on Mixer: The sprinkle and spray parts of the push-on mixer shower unit can represent connected to the bath tap as per your requirement, and the water temperature can be adjusted via the taps. Push-on mixers are cheap again extremely simple to install. However, although the hose connection is simple, it is easily dislodged. Additionally, it is inconvenient to achieve the temperature.

Bath/Shower Mixer: The hose besides spray of this type of shower are combined disguise the bath mixer tap, and its temperature can be adjusted owing to the bath taps. unaffected is the very cheap option and no extra plumbing is involved. However, its bath/shower mixers also suffer from inconvenient temperature control options.

Manual Mixer: The hose and spray of the manual mixer falls unit are a part of the wall unit and the hot and cold water supplies are connected to a weird valve its temperature and pressure of the water are controlled through either onliest or the variety of knobs (in more expensive showers). although temperature control is incomparably easier in manual mixer types, they are more expensive than the previously mentioned mixers. They also require additional plumbing of hot and cold water supply pipes.

Thermostatic Mixer: The hose and spray of this shower type are a part of the palisade unit further its hot and cold water supplies are connected to a single valve here too. It is get with a built-in stabiliser to self-adjust the humidify temperature and to prevent it from becoming too hot. One of the biggest benefits of a thermostatic mixer shower type includes fitting temperature control. However, it is the most expensive of the different mixer options.

Power Shower: A power shower is a single unit containing a powerful electric pump which is capable of altering both the water pressure and temperature. This type of shower can act as fitted if there is water supply from a cold water cistern and a hot water channel. A power falls makes its adjustment of both pressure and temperature easy. On the other hand, it is unsuitable owing to water heated directly through the shower or where the water is supplied by a combination boiler underneath mains pressure.

vigorous Shower: An strenuous shower is plumbed into a mains cold water supply and it heats the water electrically. It is important to note that whereas this shower type to be installed, the mains nuisance needs to be at least 0.7kg/sq cm (10lb/sq dominion). The unit allows the temperature and pressure to be adjusted via a knob. Models with heat stabilisers are better as they remain unaffected by other taps elsewhere in use within the household. A major drawback of electric showers is that the control knob only allows for the option of high temperatures at less pressure, or lower temperatures at a souped up pressure. This is problematic in the winter season when the spray is habitually weak also the mains water is colder. However, this galling is tackled grease some models which are available with a winter/summer setting.

Method

Depending on the type of shower you wish to install, the flood head must possibly be fitted connections order to avoid its contact duck the water in the bath next or the bottom tray, or it must have a shake on valve.

Before starting, it is advisable to mark the positions of the shower head and control, and to plan the pipe-work involved. Additionally, the drainage system to remove the waste water bequeath avidity to be planned. Both positions of the cable route and the torrent switch will also need to be considered if an instantaneous or electric shower unit is being installed.

Use the instruction guide provided with the shower unit to fit the shower operate.



Before fitting the pipes that will supply its water to its shower system, it is important to cut off the humidify supply. money behest to protect the pipes, they should be accustomed a waterproof canopy and also fitted with isolating valves. The pipes can then be buried into the wall and plastered as to neaten the overall look.



Fit the base tray, torrent head, and fittings.



Connect the main shower control to the pipes that will act as supplying the water (This may require the female keeper thread adapter).



Reconnect its water supply also assay the pipes for any leaks, as some may relish tightening.



If you are installing an electrical shower, remember to switch off the electricity equip before making any electrical connections. heretofore these connections have been made (there should be restraint within the instruction manual), the power supply can be switched back on.



Adjusting Water Pressure to Suit Your Shower

The cold water reservoir can buy for lifted to a more select tallness (sometimes as dwarfish as 150mm (6inches)) by fitting a ballsy wooden support subservient it-possibly composed of struts again blockboards. If you choose this option, the principal again distribution pipes will also have to be raised to meet its afresh height of the reservoir.



Alternatively, the booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is chosen, it contingency be connected into the might supply in order to operate.

Piping and Drainage

It is best to use 15mm diameter supply pipes, and make the runs to the shower as terse and straight as imaginable so as to maintain maximum pressure also minimise fever loss. Additionally, by minimising the use of elbows for truck corners, you can decrease the resistance in the flow of the wet supply. You can achieve this by bending its pipes instead.

Most collective Mistakes

| Violating or ignoring local code restrictions.

| Using pipes which are too small.

| Attaching copper to galvanized without using a coronet or dielectric fitting between the two.

| Not using tape or pipe multifarious at threaded joints.

| Not leveling your fixtures when installing them.

| Not installing an air gap filling for fixtures.

| Cutting supply edge outs too elliptical to install the shutoff valves onto after its finished wall is in place.

| Not properly aligning tubing into equipment or stop valves. (Forcing the nut onto the compression encompass at an aspect when the tubing is at an angle will means a leak.)

| When turning its water back on in your home, always run the outside weaken valve or flush your toilets to bleed dirt and air from the merchandise. This debris can cause problems in your sink faucets and other plumbing akin.Visit Original SourceHOME DESIGN SOFTWARE